
Showers, bathroom floors, ensuites and toilets waterproofed to AS 3740 by a licensed NSW waterproofer. Every job finishes with photos of each coat, a compliance certificate and a 10-year written workmanship warranty.
Tell us about your bathroom project. We will get back within 24 hours.
Tiles and grout are not waterproof. Water gets through grout lines every time you shower, and the only thing stopping it from reaching the floor framing, the slab or the ceiling below is the membrane under the tiles.
When that membrane is missing, too thin or not taken up the walls far enough, the damage is slow and hidden. By the time you see a stain on the ceiling downstairs or a skirting board swelling in the hallway, water has usually been escaping for months.
In the failed showers we strip out across Sydney, the same faults come up again and again:
Each one is invisible once the tiles go on. That is why we photograph every stage and hand the photos to you.

Whether you're building, renovating or fixing a leak, we waterproof every wet area in your bathroom.
The shower is where most bathroom leaks start. We waterproof the full shower floor, the walls to at least 1.8 m, every internal corner, the floor waste and every tap and pipe penetration.
Get a Quote
We waterproof the bathroom floor and turn the membrane up the walls at every wall and floor join, with reinforcing at the corners where movement cracks start.
Get a Quote
Shower walls, walls behind vanities and walls around baths. Each area is sealed to the height AS 3740 sets for it.
Get a Quote
Baths leak at the edges, not through the tub. We waterproof the hob, the walls above the bath and the gap between the bath edge and the wall, which is where water most often gets behind tiles.
Get a Quote
Ensuites usually sit over bedrooms or living areas, so a small leak does a lot of damage. We waterproof ensuites and separate toilets as their own jobs or as part of a full bathroom.
Get a Quote
Regrouting and sealing protect a sound bathroom and keep it looking clean. It does not replace a failed membrane. If water is already getting through, we will tell you so at inspection rather than sell you a surface fix.
Get a QuoteCall us for an inspection if you notice any of these:
One sign on its own does not always mean the membrane has failed. A loose tap fitting or a cracked silicone joint can cause similar symptoms. At inspection, we find the actual source before recommending any work.
Book a Moisture InspectionDamp patches or swelling on walls, skirting boards or door frames next to the bathroom.
Tiles that sound hollow when tapped, or that have lifted or cracked.
Mould that keeps coming back on grout or silicone even after cleaning.
A musty smell that stays after the room has dried out.
Paint bubbling or peeling near the shower.
Stains or drips on the ceiling below the bathroom.
Every bathroom we waterproof goes through the same five steps, so nothing gets missed.
Proven 5-Step Process
We check the substrate, the floor falls to the waste and any existing damage, then clean and prime the surface so the membrane bonds properly.
Bond breaker or reinforcing tape goes into every internal corner and wall and floor join. Puddle flanges go in at the floor waste and every pipe and tap is sealed.
The first coat goes on at the thickness the manufacturer specifies, then cures for the full time on the product data sheet.
The second coat goes on at right angles to the first so there are no thin spots or missed areas.
We check the finished membrane, photograph every area and issue your compliance certificate and 10-year written warranty.
Waterproofing is licensed specialist work in NSW. Ours is done under NSW Licence 504073C, held by Sydney One Waterproofing Pty Ltd (ABN 28 698 372 226), and every bathroom is waterproofed to AS 3740, the Australian Standard for waterproofing domestic wet areas, as referenced in the National Construction Code. What that means on your job:
Membranes applied as their technical data sheets specify.
Shower walls waterproofed to at least 1.8 m.
Reinforcing at every corner and join where movement cracks begin.
A compliance certificate you can hand to your certifier, builder, strata manager or future buyer.
Builders and certifiers: we supply photos and a compliance certificate with every job.
Discuss Your ProjectRated by 100 Sydney customers on Google.
We work right across Sydney, from the Northern Beaches and North Shore to the Inner West, Western Sydney and the Sutherland Shire.
Whether you are renovating or fixing a leak, we work around your tiler so the membrane is done, cured and certified before tiling starts.
Staged work for amenities and change rooms to keep downtime low.
Written findings with photos for committee meetings and clear scope for leaks between lots.
Two-coat membranes, photo records and certificates ready for your certifier, with scheduling that fits your trades.
Every bathroom is different, so we quote after a free inspection rather than guess over the phone. The price depends on:
The size of the area being waterproofed.
Whether old tiles and failed membrane need removing first, and the condition of the substrate and the floor falls.
The membrane system the job needs.
Access, including apartments and upper floors.
You get a written, itemised quote within one business day of the inspection, with no obligation.
A cheap membrane that fails costs far more than doing it once properly. Our quote spells out exactly what is included, the membrane we will use and what the warranty covers.
Tell us about your bathroom and we will book an inspection at a time that suits you. Prefer to talk? Call 0470 300 561.
Common questions about bathroom waterproofing in Sydney. Still curious? Our team is one call away.
Talk to a SpecialistMost bathrooms take 1 to 2 days, including the cure time between coats. Your tiler can start once the membrane has fully cured, as set out in the manufacturer's instructions. We will give you the exact date.
Bathroom waterproofing must meet AS 3740 and the National Construction Code, and must be done by a licensed waterproofer. When the work is finished, you should receive a compliance certificate. We provide one on every job.
At least two, applied at the thickness the manufacturer specifies and cured between coats. One coat leaves thin spots that fail over time.
Look for damp walls next to the bathroom, hollow or lifting tiles, mould that returns, a musty smell or a ceiling stain below. An inspection confirms whether the membrane has failed or the cause is something simpler.
Yes. Showers, ensuites and toilets can each be done as a standalone job.
A 10-year written workmanship warranty from us, plus the membrane manufacturer's product warranty.
It depends on size, the condition of the existing surface, the membrane system and access. We inspect for free and send a written quote within one business day.
Before. The membrane goes onto the prepared substrate, cures, and then the tiles go on top.
Surface sealers can slow a minor leak for a while, but they do not repair a failed membrane underneath. Where the membrane has failed, we remove the tiles, replace the membrane properly and certify it. For leaks that need diagnosing first, see our bathroom leak repair service.
Your trusted partner for expert waterproofing solutions, ensuring long-lasting protection for your home and business from water damage.
NSW Licence: 504073C
ABN: 28 698 372 226
ACN: 698 372 226
Copyright © 2026 All Rights Reserved.
Free, no-obligation quote. We'll get back to you within 24 hours.